image
Curing Ovens

Curing conveyor 60°

curing conveyor 60

Specification:

  • Buffer 3 pcs products.
  • Segmented Belt Track.
  • Segment length = 500 mm.
  • Curing oven based on hot air
  • Controlled by Omron PLC
  • Communication via SMEMA standard
  • Vertical air flow
  • Adjustable air temperature
  • Adjustable curing time.

 

Hot Air Curing Conveyor 1500-3 150 degrees.

hot air curing conveyor 150

Specification:

  • 1 pcs. Chain Segment conveyor.
  • Conveyor length 1220 mm.
  • PCB width = 460 mm.
  • Electrical width adjustment.
  • Fixed rail at the FRONT side.
  • Adjustable curing time by PLC.
  • Curing conveyor based on hot air, reflow system; vertical airflow.
  • Electrical heating system, PID controlled by solid state switches; adj. air temperature.
  • Isolated top-cover.
  • Controlled by Omron PLC and NQ3 touch screen.
  • Communication via SMEMA standard

Gates:

  • In- and outfeed gate to avoid loss of heated air

Buffer mode:

  • Buffer mode can be activated, so that ‘maximum number of boards’ can stay in the oven. To pick up the next board, the track returns, so that the distance between the boards will be minimized.
  • number of boards be programmed by the NQ3 touch screen.

Temp profiles:

  • Temp profiles can be defined by the NQ3.
  • curing time programmable.
  • Alarm as curing time is passed and board can not leave the oven (failing smema).

Exhaust connection foreseen.

  • Exhaust connections at entrance and outgoing side are foreseen.
  • Exhaust to be connected on factory exhaust system.

 

CM 1500-1-500 IR Curing System.

 cm- 1500-1-500 IR curing system

General.

  • Curing length L =1220
  • Track length L=1500 ; 1 segment; micro chain transport, 5 mm edge, driven by stepper motor; speed 0.15 – 6 m/min.
  • In- and outfeed gates.
  • PCB temp. = 200o C
  • Direct temp. Measurement on the PCB.
  • / max. PCB width = 50 – 500 mm.
  • Top-Bottom component clearance 90 mm.
  • Power requirements, 3×380 VAC, 32 Amp.
  • Motorized width adjustment.
  • OMRON PLC controlled and NQ3 touch screen.
  • SMEMA interface at Infeed and outfeed
  • Colour RAL 9002.

 lower section IR lamps

InfraRed heating system.

  • 2 INFRARED heating zones.
  • 1 pcs. Top- and 1 pcs. Bottum zone.
  • Lamps build in panels.
  • IR Panels can be taken out , for maintenance purposes.
  • Lamps are mounted across transport direction.
  • Number of lamps activated depending on conveyor width (2 sections).
  • Bottom panels foreseen with glass plate.
  • Heat intensity analogue adjustable through Thyristor power controller.
  • PID controller / zone.
  • Heating time adjustable.
  • At start up, the transport starts after a pre-defined time.

 upper section IR lamps

Buffer mode:

  • Buffer mode can be activated, so that ‘maximum number of boards’ can stay in the oven. To pick up the next board, the track returns, so that the distance between the boards will be minimized.
  • number of boards be programmed by the NQ3 touch screen.

Temp profiles:

  • Temp profiles can be defined by the NQ3.
  • curing time programmable.
  • Alarm as curing time is passed and board can not leave the oven (failing smema).

 exhaust at backside

Exhaust connection foreseen.

  • Exhaust van include; cap. 800 m3 /hr to lower the area temp in the oven and to get the oven ex-proof.
  • Exhaust to be connected on factory exhaust system.

Temp measuring.

  • Measure the temp inside the oven by PT100 elements.
  • Measure the temp of the board by IR contactless temp measuring device.

Earth leakage and Phase orientation.

  • Earth leakage switch included.
  • Phase orientation control included.

 

UV Fusion Curing oven

UV Fusion Curing Oven

Specification:

  • L = 1950 mm
  • 3 pcs. transport section; pin chain transport, boards supported on 3 mm. edge.
  • Width adjustment 50 – 460 mm
  • Curing oven based on 2 pcs. Fusion UV lamps F300-12-120w/cm, suitable for 300 mm. curing width.
  • Adjustable height of the lamps; passtrough height trough +/- 90 mm.
  • Full control of the UV lamps by PLC
  • Adjustable transport speed 0,5 – 3,0 m/min.
  • 2 infeed gates and 2 outfeed gates
  • Controlled by Omron PLC and NQ3 touch screen.
  • Colour RAL 9002
  • Communication via SMEMA standard

Gates:

  • Due to high intensity In and Out-feed gates needed, to avoid UV radiation to the area (safety).

F300-12-120 w cm

Exhaust included:

  • Exhaust van 800 m3/hr to lower the area temp inside the UV curing zone.
  • Temp in Curing Area is PID controlled.

Option:

  • 3th Fusion lamp for additional width.

 

UV Flood Lamp Curing oven

UV curing oven flood lamps

Specification:

  • Curing oven based on UV Flood Lamp
  • Curing width: 127 mm/lamp system.
  • 2 pcs. lamp systems installed.
  • curing width is 255 mm.
  • Typical intensity in the UVA range (320-390 nm), measured 3” from bottom edge of the reflector housing: 225mW/cm2
  • Controlled by Omron PLC
  • Operator interface by Omron NQ3 touch screen.
  • Communication via SMEMA standard
  • Adjustable speed by inverter

Gates:

  • In and Out-feed covers (no gates); gates in combination with a shutter can be offered as an option, to avoid getting UV radiation in the area around.
  • In and Outfeed gates can be added against extra costs: Euro 2.250,00

Exhaust:

  • Exhaust van 800 m3/hr to lower the area temp inside the UV curing zone.

Note:

  • Intensity 225mW/cm2
  • 2 pcs. Lampsystems incl.

Option:

  • 3rd lamp system.

 

Magazine Curing oven

magazine curing oven 1

Specification:

  • Products cured within the magazines
  • Magazine transport through the oven
  • Curing oven based on hot air
  • Magazine L/ W /H 220x265x563 mm
  • Controlled by Omron PLC
  • Communication via SMEMA standard
  • Adjustable air temperature
  • In an out-feed covers
  • 2 in-feed gates and 2 out-feed gates

magazine curing oven 2

 

Double track Curing oven

double track curing oven

Specification:

  • Curing oven based on hot air
  • Double tracks
  • Controlled by Omron PLC
  • Communication via SMEMA standard
  • Adjustable air temperature
  • In an out-feed covers